1. The driven plate assembly should be kept clean, and the friction plate must be dustproof, dirt proof and oil proof. Before the clutch is assembled on the engine, the surface of the pressure plate and the flywheel should be scrubbed to remove the oil stain, so as to prevent the clutch from slipping. The clutch is generally adjusted before leaving the factory. There is no need to adjust it in use. If it needs to be adjusted, special process tools must be used to adjust it to prevent the pressure plate from tilting.
2. 為了保持離合器工作的平穩性，離合器壓盤總成及從動盤總成在出廠之前已經進行了平衡，使用中不要隨意的拆換零件，離合器修理必須拆開時，一定要先做好記號，修理后按原記號裝配并重新平衡。 在發動機上裝配或拆卸離合器時，必須對角交替打緊或放松離合器固定在飛輪上的螺栓或螺母。
2. In order to maintain the stability of the clutch, the clutch pressure plate assembly and the driven plate assembly have been balanced before leaving the factory. Do not replace the parts at will during use. When the clutch must be disassembled for repair, make marks first, and then assemble according to the original marks, and pay attention to the new balance. When assembling or disassembling the clutch on the engine, the bolts or nuts fixed on the flywheel by the clutch must be tightened or loosened alternately diagonally.
3. 大型混凝土攪拌機安裝離合器時，要用耐溫、耐壓的潤滑油脂適當?shù)臐櫥瑥膭颖P花鍵和變速箱1軸花鍵，保證從動盤在變速箱1軸花鍵上能自由移動，但是過量的潤滑油會引起摩擦片打滑，所以一定要注意這一點。
3. When installing the clutch of large concrete mixer, the driven plate spline and gearbox 1 shaft spline should be properly lubricated with temperature resistant and pressure resistant lubricating grease to ensure that the driven plate can move freely on the spline of gearbox 1 shaft. However, excessive lubricating oil will cause friction plate to slide, so we must pay attention to this point.
4. 大型混凝土攪拌機安裝時必須十分注意，不要損傷從動盤花鍵，防止從動盤軸向移動因毛刺卡滯而不能分離。 必須保證離合器分離行程符合要求，分離行程過大，容易使分離桿碰上從動盤帶來危害，分離行程過小，將使離合器不能徹底分離。
4. During the installation of large-scale concrete mixer, great attention must be paid not to damage the spline of driven plate, so as to prevent the driven plate from being separated due to burr sticking due to axial movement. It is necessary to ensure that the clutch separation stroke meets the requirements. If the separation stroke is too large, it is easy to make the release rod touch the driven plate, which will bring harm. If the separation stroke is too small, the clutch can not be completely separated.
5. 離合器處于接合狀態時，分離軸承與分離環之間應保持2-3mm的間隙，這樣在摩擦片磨損的情況下就不會妨礙壓盤壓緊摩擦片。摩擦片磨損規定磨損極限時，應及時更換從動盤總成，以免離合器打滑并劃傷壓盤及飛輪表面。
5. When the clutch is engaged, a clearance of 2-3mm should be maintained between the release bearing and the release ring, so that the pressure plate will not be prevented from pressing the friction plate when the friction plate is worn. When the friction plate is worn to the specified wear limit, the driven plate assembly should be replaced in time to avoid the clutch slipping and scratching the pressure plate and flywheel surface.
6.正確使用，避免操作不當引起離合器打滑。在攪拌車的日常使用中，要注意對離合器分離操縱機構的檢查，及時排除泵及管路的滲漏的故障，保證離合器正常工作。
6. Use it correctly to avoid clutch slipping caused by improper operation. In the daily use of the mixer, attention should be paid to the inspection of the clutch release control mechanism, and the leakage fault of the pump and pipeline should be eliminated in time to ensure the normal operation of the clutch.
今天小編給大家介紹的是關于小型混凝土攪拌車的相關知識，更多的精彩內容請點擊我們的網站咨詢：http://www.qirongguanjia.cn我們后續會有更多的知識為您奉上。
Today, I'd like to introduce to you the relevant knowledge about small concrete mixer truck. For more wonderful contents, please click our website: http://www.qirongguanjia.cn We will have more knowledge for you.
