在生產混凝土?xí)r，混凝土攪拌車由于一整天在處于開機狀態，因此溫度多少度是正常的，如何科學的進行溫度檢測管理，這對生產工作來說非常重要。那么混凝土攪拌車的溫度如何進行有效管理？

　　In the production of concrete, the concrete mixer is in the boot state all day long, so how much temperature is normal, how to scientific temperature detection and management, which is very important for the production work. So how to manage the temperature of concrete mixer truck effectively?

　　施工環境的溫度檢測，每天在10點、14點、18點三個時間段進行觀測；對攪拌材料和防凍劑溫度的測量，每工作班不少于3次；對生產出混凝土少3小時檢測一次；對灌筑前和振搗完畢的溫度，少每2h測量一次。

　　The temperature of the construction environment is detected at 10 o 'clock, 14 o 'clock and 18 o 'clock every day. Measurement of mixing materials and antifreeze temperature, not less than 3 times per working shift; At least 3 hours to produce concrete inspection; The temperature should be measured at least every 2 hours before and after filling.

　　對養護期間混凝土溫度的測量：在終凝前，前三天每2h測一次，以后每晝夜指數應進行2次。在超過養護期后，在環境發生變化時進行抽檢7.為了測量砼內部的溫度，應在澆灌砼時預埋一些一端封閉溫管中，并立即加以覆蓋，以免受外界氣溫影響，溫度計在管中指數停留5分鐘，然后取出，迅速記下溫度。

　　Measurement of concrete temperature during curing: before the final setting, the first three days should be measured every 2h, and the index should be carried out twice every day and night after that. 7. In order to measure the internal temperature of concrete, some end of the closed temperature tube should be embedded in the pouring concrete, and immediately covered, so as not to be affected by the external temperature, the thermometer stays in the tube index for 5 minutes, and then removed, quickly write down the temperature.

　　混凝土攪拌車廠家提醒，混凝土攪拌車的操作也應該是正確的，比如：混凝土攪拌車安裝平穩牢固，行走輪要離開地面，機座要高于地面；開機前電氣設備良好，空轉運行待機械運轉正常后，再加料攪拌；混凝土攪拌車操作中邊加料邊加水，不能加入料后再啟動。等等。

　　Concrete mixer manufacturers remind that the operation of concrete mixer should also be correct, such as: the installation of concrete mixer is stable and firm, the walking wheel should leave the ground, the base should be higher than the ground; Before starting the electrical equipment is good, idling operation to be normal mechanical operation, and then add stirring; Concrete mixer truck operation in the side of adding water, can not add material after starting. And so on.

　　如果作業中發生故障，應及時斷電停機，查找原因，不得用工具撬動等危險方法，強行機械運轉?？傊⒁獾氖马?xiàng)還有很多，如果您有其他問題就來網站www.qirongguanjia.cn進行咨詢吧。

　　If there is a failure in the operation, it should be cut off in time to find the cause, and it is not allowed to use tools to pry and other dangerous methods to force the mechanical operation. In short, there are a lot of matters to pay attention to, if you have other questions to consult the website www.qirongguanjia.cn.