小型混凝土攪拌車卸完料后，卸了料門關閉，但無關門信號，造成程序停止運行，這是怎么回事呢？又該如何來呢？

After unloading of small concrete mixer truck, the unloading door is closed, but there is no door closing signal, causing the program to stop running. What is the matter? How to solve it?

原因分析：

Cause analysis:

小型混凝土攪拌車卸料門接近開關與卸料門上的轉柄指針接近距離不超過5mm才能感應信號。當卸料門因油泵壓力未達到要求或卸料門在關閉時被小型混凝土攪拌車里的殘料卡住時，接近開關接近不到轉柄指針而沒有信號，因接近開關或轉柄指針松動，使接近距離超過5mm時，接近開關也感應不到信號。如接近開關損壞也沒有信號輸出。

The proximity switch of the discharge door of the small concrete mixer truck can sense the signal only when the proximity distance between the rotary handle pointer on the discharge door is no more than 5mm. When the discharge door fails to meet the requirements due to the pressure of the oil pump or the discharge door is stuck by the residues in the small concrete mixer truck when it is closed, the proximity switch cannot reach the rotary handle pointer and has no signal. When the proximity switch or the rotary handle pointer is loose, the proximity switch cannot sense the signal when the proximity distance exceeds 5 mm. If the proximity switch is damaged, there is no signal output.

處理過程：

Handling process:

1.檢查卸料門液壓系統工作壓力是否達到要求（13Mpa）

1. Check whether the working pressure of the hydraulic system of the discharge door meets the requirements (13Mpa)

2.切換到手動，把小型混凝土攪拌車卸料門打開，使卡住的殘料掉落后再關上

2. Switch to manual mode, open the discharge door of small concrete mixer truck, and close it after the stuck residue falls

3.檢查接近開關和轉柄指針是否松動

3. Check whether the proximity switch and the rotary handle pointer are loose

4.檢查接近開關是否損壞

4. Check whether the proximity switch is damaged

小型混凝土攪拌車如果長期閑置停放或封存保管時就需要進行的一種維護保養。保養內容主要是清潔、清洗、潤滑、防護等。其目的是預防或減少存放期間各種惡劣條件對機器產生的不良影響，保證車輛經常處于良好的備用狀態。

It is a kind of maintenance required for small concrete mixer if it is left idle for a long time or sealed for storage. The maintenance mainly includes cleaning, cleaning, lubrication, protection, etc. Its purpose is to prevent or reduce the adverse effects of various harsh conditions on the machine during storage, and ensure that the vehicle is always in good standby state.

小型混凝土攪拌車卸料門關門無信號的原因以及處理內容就講解完畢了，您如果遇到類似問題不了歡迎來聯系我們http://www.qirongguanjia.cn！

The reason why there is no signal when the discharge door of the small concrete mixer is closed and the handling content have been explained. If you encounter similar problems and cannot solve them, please contact us http://www.qirongguanjia.cn ！