Proper lubrication of the chassis of cement mixer truck can reduce the wear of vehicle parts and increase the service life of mixer truck parts. However, the following points should be paid attention to during lubrication:
1、正常使用情況下，按攪拌車廠家的保養周期進行潤滑，環境惡劣情況下要適當縮短保養周期。
1. Under normal use, it shall be lubricated according to the maintenance cycle of the mixer manufacturer, and the maintenance cycle shall be appropriately shortened under bad environment.
2、要選用規定的潤滑油。代用油料須性能接近，主要技術指標須保證，并且用代用油應時常檢查，且縮短使用周期。
2. The specified lubricating oil shall be selected. The performance of substitute oil shall be close, the main technical indexes shall be guaranteed, and the substitute oil shall be checked frequently to shorten the service cycle.
3、更換發動機機油時，要在熱狀態時進行，以保證油能放盡。放油時應注意檢查機油顏色是否正常、機油有無異物，以便發現故障隱患。待油放盡后，放油螺栓上的異物，然后擰緊。
3. When changing engine oil, it shall be carried out in hot state to ensure that the oil can be drained. When draining the oil, pay attention to check whether the oil color is normal and whether the oil has foreign matters, so as to find hidden troubles. After the oil is drained, remove the foreign matters on the oil drain bolt, and then tighten it.
4、進行潤滑前，要清潔入口。潤滑后要清潔零件表面，以免沾上塵土和污物
4. Clean the inlet before lubrication. Clean the surface of parts after lubrication to avoid dust and dirt
5、更換新機油濾芯，將新機油注入發動機到油尺上限。為防止在沒有潤滑油的情況下啟動發動機，應使高壓油泵處于斷油位置時按啟動按鈕，空轉一會兒后，再啟動發動機，并低速運轉。檢查機油濾清器有無滲漏，停機后，檢查并補充機油油面到油尺上。
5. Replace the new oil filter element and fill the engine with new oil to the upper limit of the dipstick. In order to prevent starting the engine without lubricating oil, press the start button when the high-pressure oil pump is in the oil cut-off position, idle for a while, then start the engine and run at low speed. Check the oil filter for leakage. After shutdown, check and replenish the oil level on the dipstick.
6、換機油濾芯：更換機油時，機油濾清器要同時更換，在密封墊上涂上一層薄薄的油，并且緊固濾清器。
6. Oil change filter element: when changing the oil, replace the oil filter at the same time, apply a thin layer of oil on the sealing gasket, and fasten the filter.
以上就是小型混凝土攪拌車http://www.qirongguanjia.cn為大家介紹的內容，感謝您在百忙之中查看我公司的信息內容，如果您想要了解的更多，歡迎您來電進行咨詢!
The above is a small concrete mixer http://www.qirongguanjia.cn Thank you for checking the information of our company in your busy schedule. If you want to know more, you are welcome to call for consultation!
